Best Laser Printer Machine Sale Choice Collections provide printer machine,new printer,thermal printer Great Clearance Micromake 3D Printer Makeboard Mini Control Board Main Control panel Compatible Ramps 1.4. Get Discount Now! Only US $36.62/piece at this time. Hurry buy Now before back to normal price! Normal price US $40.69 or you can Check price now. Dont waste your time. Buy Now only in TZT Trusted Seller Store!
Micromake 3D Printer Makeboard Mini Control Board Main Control panel Compatible Ramps 1.4
Product Description:
- Makeboard Mini is specially designed by Micromake Technical Team to solve the problem which usually occurs on the open source control board of Ramps 1.4 3d printers. It’s suitable for 3D printer DIY kits manufacturer in particularly. The more kits you purchase, the cheaper. Please discuss with customer service on Trade Manager.
- We take stablity, heat dissipation and concision into account and the effect has verified by Micromake 3d printers, we had sell almost two years and thousands of our products, there are few errors about the control board.
- We had fully consider about the mistakes that customers usually make in the beginning, so we use different color to distinguish different connector, and use XH connector to avoid reverses.
- We give enough protection in the circuit program. The board adopt dual self-recovery fuses to avoid short-circuit and 4-way high resistance diode to avoid reverse so you will not damage the board even if the wire of power sully is insert oppositely.
The design of Pin is compatible with RAMPS 1.4 control board, you can download the open source firmware of Marlin or Repetier and so on to use directly.
- Support 1602,2004,12684 display, insert EXP1, EXP2 connector, meanwhile , with AUX1 connector the touch color screen is available.
The size of this board is 10*8.5cm, the 4 setting hole use M3 screws, the center of the hole is 4.5mm far from the edge.
- Support many kinds of 3D printer with transmission structure. All of printers are selling in Micromake use the control board.
Open source printer firmware for your reference, which makes it easier for DIY beginners to get start.
You can see related material and course in offical website of Makeboard: http://www.makeboard.org
- The distinction from Makeboard Pro:It has integrated driver chip so you needn’t extra purchase. Easier assembly, Mini size and matched Acrylic shell as a gift. What’s more, it supports both DC interface and terminal block for power supply. You can use DC power supply without using heated bed, it’s simple and beautiful.
The update compared to Micromake 1.3:
- Enhanced power supply circuit, adopted professional power management chip, support 40V input wide voltage at most while the previous 1.3 version only support 12V.
- Integrated driver chipis updated from 16, 32 microstep2 stepper modes to 16, 32, 64, 128 microstep4 stepper modes.
- It has both DC interfaceand terminal block for your choice of power supply mode according to the situation while the previous 1.3 version can only choose one from two.
The drive chip Features:
- The drive chip can support 128 microstep at most and can be adjusted by MS1, MS2 jumper on the control board. H means short circuit, and L means disconnecting.
- If you need to adjust current, please put the positive electrodes of multimeter into screw hole on adjustable resistor and put negative electrodes on USB shell after restarting printer.
T- he measured voltage divided by 0.8 equals current of drive chip. Eg: If the default voltage is 0.6V, the current is 0.6/0.8=0.75A.
- Please be sure to cut off power first, then rotate adjustable resistor with screwdriver. Turn left to decrease the value, turn right to increase the value. Don’t screw too much at one time, 30°is OK.
- Turn on the power after adjustment, then measure the voltage, if it isn’t appropriate, please cut off the power and adjust again. Emphasize again, be sure to cut off power before screw the adjustable resistor.
- It’s not recommended to adjust current without multimeter. We have set the recommended value at the factory. It’s 0.75A for XYZ motors, 1A for E motor.
- It’s wrong to say the bigger current, the better. High current will cause hot motor. If XYZ motors are too hot, they will fall out step. If E motor is too hot, the filament will become too soft to squeeze out.
Instructions:
- In the pin definition diagram, GND means negative electrodes, VCC means +5V, VIN means input voltage. For example, if you use 24V power, VIN expresses as +24V.
Marlin and Repetier firmware’s definition to pin:
Eg: Digital IO D38 is written as 38;
Analog IOA1 is written as 1+54=55, A2 is written as 56.
- If you don’t use heated bed, you can directly plug DC power supply above 5A into DC jack to supply electricity without extra wiring. It’s simple and safe.
- If you need to use heated bed, please connect switch power supply above 15V with connector according to “The top is positive and the below is negative.†Then plug it into POWER jack.
- You can use 5V-40V power supply, please note that the heating wire, heated bed, motor and fan have to be corresponding voltage. 12V, 24V is commonly used.
- For non-Delta structure printer, you need modify pin definition of limit switch. You just need to modify a code according to your firmware type in the following way.
- If you use Marlin firmware, please open pins-RAMPS.h file, press Ctrl+F to search X_MIN_PIN.
Then change X_MIN_PIN into 2, Y_MIN_PIN into 15, Z_MIN_PIN into 19, the code as follows:
- If you use Repetier firmware, please open pins.h file, press Ctrl+F to search #ifdef RAMPS_V_1_3.
Then change ORIG_X_MIN_PIN into 2, ORIG_Y_MIN_PIN into 15, ORIG_Z_MIN_PIN into 19, the code as follows:
Note:We will test the control board before shipment, it wouldn’t be sent out unless we ensure it can work normally.
Please be sure to cut off power before any wire plug in and pull out operation on control board when using.
Package List:
- 1 x Micromake 3D Printer Makeboard Mini Control Board Main Control panel
1) We accept Alipay, West Union, TT. All major credit cards are accepted through secure payment processor ESCROW.2) We will process most order in 48 hours after payment verification and offer tracking no with every Deal(aliexpress only can fill the tracking No after 24 hours).3) Support WORLDWIDE SHIPPING. (Except some countries and APO/FPO).4) DHL/Fedex Tracking No Maybe Change after the item arrive Hongkong(eg.we shipped the item on Friday and fill the tracking No,but the tracking No may be Change on Monday if the Parcel arrive Hongkong).5) SERVICE TRANSIT TIME is provided by the carrier and excludes weekends and holidays. Transit times may vary, particularly during the holiday season.6) If you have not received your shipment within reasonable days from payment, please contact us first(pls dont put negative feedback before contact us!). We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
1) We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important ,We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.2) It is impossible to address issues if we do not know about them!
1) For Russian buyer,pls offer full name as policy requires.2) For Buyer from Russian Federation,Argentina,Ukraine,Item may ship via EMS if you choose DHL/Fedex as complex customs declaration process.3) For Buyer From Brazil,pls offer Tax No is you want to ship via DHL/Fedex,or item will ship via EMS though you choose DHL.
Return Policy
If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.
Seller Service
On-time Delivery: If you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).Great Clearance Micromake 3D Printer Makeboard Mini Control Board Main Control panel Compatible Ramps 1.4
No comments:
Post a Comment